4 Symptoms of a Bad Clutch Master Cylinder (and Replacement Cost)

Last Updated on November 21, 2022

A clutch master cylinder links your left foot to the clutch in a three pedaled vehicle with a hydraulic clutch. If the master cylinder has completely failed, it will likely leave you stranded, unless you can figure out a way to limp home without the use of the clutch. This is especially dangerous if the brake and clutch share the same reservoir, as you could be left without brakes as well. 

Fortunately, the most common failure mode of a clutch master cylinder is leaking clutch fluid, which may give you some early warning signs before the system fails completely.

Need help with a car problem RIGHT NOW?
Click Here to chat online with a verified mechanic who will answer your questions.

How a Clutch Master Cylinder Works

Modern vehicles with a manual transmission use hydraulic fluid (usually brake fluid) to transfer the movement of the clutch pedal into an actuation of the clutch fork. When you depress the clutch pedal, a rod attached to the clutch pedal assembly pushes on hydraulic fluid in the clutch master cylinder.

Since this fluid is not compressible, it is forced to travel down the clutch lines to the slave cylinder, which is attached to the clutch fork. The clutch fork forces the clutch to separate from the pressure plate and flywheel, allowing the engine and wheels to spin independently.

See Also: Common Causes of a Manual Transmission That’s Hard to Shift

Top 4 Bad Clutch Master Cylinder Symptoms

Here are four of the most common signs your clutch master cylinder is starting to fail or has already completely failed. Note that the following are likely only helpful if you have a hydraulic clutch problem, and don’t apply to a cable operated clutch system.

#1 – Low Clutch Fluid

low clutch fluid

A clutch master cylinder will have low and high marks on the side of the reservoir indicating a safe volume of clutch fluid. If your clutch fluid level falls below the low mark, it’s time to top up. The reservoir cap or owner’s manual should tell you what type of fluid to use.

Once you top up your clutch fluid, keep an eye on the level. The clutch fluid level should not drop over time like you might see in brake fluid. Brake fluid level drops over time because the brake caliper piston extends further as your brake pads wear, but the clutch does not operate this way.

A chronic loss of clutch fluid is indicative of a leaking clutch master or slave cylinder. 

#2 – Soft or Spongy Clutch Pedal

how to adjust clutch pedal

Have you noticed your clutch pedal feeling a bit lighter and easier to depress than it used to? Unlike clutch fluid, air is compressible. If you have air in the clutch master cylinder, the pedal will start to feel very soft, even if the clutch seems to work perfectly.

Try bleeding the clutch to resolve the problem. If the issue returns after a bit of time has elapsed, the clutch master cylinder may be at fault.

See Also: 5 Signs of a Slipping Clutch

#3 – Engagement Point Suddenly Changed

clutch pedal adjustment

On your way to work one morning, you almost stall a couple times and can’t seem to get the car moving without jerking all over the place. You swear you know how to drive stick, maybe you’re just tired.

If this has happened to you, it might be a good idea to pop the hood and check the clutch fluid level.

If the clutch fluid reservoir is empty, there may be a tiny bit of fluid left in the lines to keep you going, but you’ll definitely notice a difference in clutch engagement, if you’re even able to get it into gear at all.

The clutch will engage right off the floor and very abruptly in this situation.

Related: How to Adjust a Clutch Pedal on a Car

#4 – Dark Clutch Fluid

dark hydraulic fluid

If you’ve changed your clutch fluid recently but notice it’s suddenly become very dark, one of the internal seals in the clutch master cylinder may be failing. Bits of rubber in these seals can break down and contaminate the clutch fluid, very quickly discoloring the contents of the reservoir.

If you haven’t changed your clutch fluid recently, check your owner’s manual for the recommended maintenance interval. The proper way to change clutch fluid is to flush the system with fresh fluid, bleeding the clutch lines in the process.

However, you could also try the following as a quick and dirty test for a failing seal since clutch fluid is cheap:

  • Suck the old clutch fluid out of the reservoir (using something like a turkey baster, for instance).
  • Top off the reservoir with fresh fluid.
  • Wait a couple days to see if the new fluid turns dark.
  • If your fluid gets dark within a couple days, it is likely you have a failing seal in the clutch master cylinder, especially if you exhibit any other symptoms listed above.

Clutch Master Cylinder Replacement Cost

Best places to order parts?  See: 19 Best Online Auto Parts Stores

clutch master cylinder replacement cost

Depending on the vehicle, replacing the clutch master cylinder is often fairly cheap and easy. It is even possible for most home mechanics to tackle this job themselves.

In some vehicles, all that is needed is to buy a new clutch master cylinder, unscrew the clutch line, unbolt the clutch master cylinder from the firewall and install the new unit (reverse the procedure).

If having a professional replace your clutch master cylinder, expect to pay somewhere in the range of $180 to $420 total.

Parts will usually cost $100 to $300. It shouldn’t take them more than an hour to replace the cylinder so you’re looking at $80 to $120 for labor in most cases.

Note: It is often recommended to replace the clutch slave cylinder at the same time as the master cylinder. When one of these parts fails, it’s often the case that the other part follows suit soon after.

Some clutch master cylinders can be rebuilt to cut costs. Most units are supposed to be bench bled before installation. The clutch pedal will likely need adjustment after replacement of the clutch master cylinder. Consult your specific vehicle’s factory manual for more information. 

15 thoughts on “4 Symptoms of a Bad Clutch Master Cylinder (and Replacement Cost)”

  1. Ive got a 87 ford ranger 2.9 L v6 and I can see where the clutch master cylinder is leaking fluid onto the floor. The resivor is always low or empty and the clutch goes from acting normal to engaging when it pushed to the floor and than if I come to a stop I have to throw it in neutral or it’ll die, than I have to pump the petal or turn the truck off just to get it back in first gear or reverse. Its really hard to shift gears when it does this, which is most of the time, sometimes I dont even use the clutch to upshift or downshift, I just get the rpms right and it’ll drop into gear, like flooting the gears in a tractor trailer. Ive been driving it like this for about half a year now.

    Reply
  2. It’s good to know that a difference in clutch engagement can mean a lower clutch fluid level. Last night I noticed that my clutch on my Ford truck feels more stiff than usual. I’ll be sure to take it into the shop to make sure my clutch can last longer.

    Reply
  3. Us there any problem if the original size of clutch master cylinder in suv car is 5/8″ that cylinder..then i changed to 3/4″ size of clutch cylinder

    Reply
    • I’m not sure, I would do some research on that. If you change the size it may change brake pedal feel, travel, or effectiveness. It’s one of those things where I would be sure I understood the implications before swapping it out.

      Reply
  4. My 2012 manual transmission Ford Feista didn’t want to down shift at all but once u shut the car if it shifts fine. Then I couldnt get it into to first.now the car When I start it just takes off and when I have the clutch in. If I hit the brake it acts like it’s gonna die

    Reply
  5. My hyundai elantra 2008 have the same problem. From last 2 years i’ve changed master cylinder 4times. Car is on 350k kms but still runs fines, the only problem is this master cylinder. The only solution is to sell the car now.

    Reply
  6. Hi
    My clutch master cylinder is about 28mth old.
    About8 mths ago my pedal went strait to the floor.
    We replaced the rubbers, I noticed it had split the bottom.
    About 6wks later, it did the same thing, split the rubber, two days ago, the same thing, yesterday morning did it again, within a few miles drive in town, it done it yet again.
    What will cause it to split new seal?
    Botton pressure seal new the spring.

    Look forward to an explanation.
    Thank you

    Reply

Leave a Comment